1. For the newly installed furnace body, before commissioning, carefully check whether the gas meets the requirements of the burner; check whether the detection instruments on the gas supply pipeline are normal and whether the opening and closing of the pipeline valves are normal, and whether it is convenient for future use and maintenance.

2．对新安装的管道，应认真检查所有管路的安装可靠性和管路的密封性。

2. For newly installed pipelines, the installation reliability and sealing of all pipelines shall be carefully checked.

3．使用单独气化站的用户，要保证供气量、供气参数符合燃烧要求。

3. Users who use separate gasification station should ensure that the gas supply quantity and gas supply parameters meet the requirements of safe combustion.

4．操作人员认真阅读设备使用说明书，熟练掌握操作知识及方法。

4. Operators carefully read the equipment operation manual and master the knowledge and methods of safe operation.

5．天然气锅炉燃烧器每次开机前要检查燃气阀门是否打开，否则燃烧器不工作。

5. Check whether the gas valve is open before starting the burner of natural gas boiler, otherwise the burner will not work.

6．启动控制柜上的电源控制按扭，此时数显表就显示当前炉内温度，新安的装炉体此温度为环境温度。

6. Start the power control button on the control cabinet. At this time, the digital display will display the current temperature in the furnace. This temperature of Xinan furnace charging body is the ambient temperature.

7．启动风机控制按扭，安装在炉体上的风机就工作，此时若风机损坏控制柜就自动保护不进入下一步操作。

7. Start the fan control button, and the fan installed on the furnace body will work. At this time, if the fan is damaged, the control cabinet will be automatically protected from further operation.

8．助燃风机工作无异常现象时，再启动燃烧控制按扭，此时燃烧程序控制器就开始工作，它通过一定的程序进行点火、送气、检测火焰、等程序更终实现燃烧。

8. When there is no abnormal phenomenon in the combustion fan, the combustion control button will be started again. At this time, the combustion program controller will start to work. It will carry out ignition, air supply, flame detection and other procedures through certain procedures, and finally realize safe combustion.

9．天然气锅炉燃烧器当燃烧控制器收到不利于燃烧的信号（例：点火失败、气压不稳定、电路有问题）等问题时，燃烧控制器就立刻关闭燃气并发出报警信号。

9. When the combustion controller receives the signal that is not conducive to combustion (e.g. ignition failure, air pressure instability, circuit problems) and other problems, the combustion controller will immediately shut down the gas and send out an alarm signal.

10.燃烧控制器若报警，必须是故障后由操作人员对其手动复位才可以继续工作。

10. If the combustion controller gives an alarm, it must be reset manually by the operator after the fault is solved.

11.整个设备的操作，操作人员应参考炉体操作规程及生产工艺要求进行操作。

11. For the operation of the whole equipment, the operators should refer to the furnace safety operation regulations and production process requirements.

12.按生产工艺要求需要调整控制温度时，操作员应参考智能数控表说明书进行调节。

12. When the control temperature needs to be adjusted according to the production process requirements, the operator should refer to the manual of intelligent numerical control table for adjustment.

（二） 天然气锅炉燃烧器关机操作

（2） Shutdown operation of natural gas boiler burner

（1）关机有两种情况：是：当炉内温度到达所设定值自动关机，此时操作员不必任何操作，等到炉内温度低于设定值时控制器会自动开机。

(1) There are two cases of shutdown: the first is: when the furnace temperature reaches the set value, the operator does not need any operation, and the controller will automatically start up when the furnace temperature is lower than the set value.

（2）第二是：人为停机和交接班停机时，此时操作员应按开机时的相反顺序（a.先关闭燃烧控制按扭、b.再关闭风机按扭、c.关闭电源按扭）操作关机。

(2) The second is: in case of man-made shutdown and shift change shutdown, the operator should operate and shut down in the reverse order (A. first turn off the combustion control button, B. then turn off the fan button, C. finally turn off the power button).

（3）天然气锅炉燃烧器关机时间较长情况下操作员应关闭燃气管路阀门，以免燃气泄漏现象发生。括和常识考查。内容概括摘原文，常识考查适当须积累文学、文化常识。

(3) When the burner of natural gas boiler is shut down for a long time, the operator should close the gas pipeline valve to avoid gas leakage. General knowledge examination. It is necessary to accumulate common knowledge of literature and culture.